ams extends magnetic position sensors portfolio with automotive-grade and ISO26262 safety-compliant dual die integrated circuits ams erweitert seine Produktpalette für ISO26262 Applikationen im Automobil mit den Dual-Chip Winkelsensoren AS5270A/B
2017/07/05
With dual-die redundancy, full data path diagnostics and enhanced self-test capabilities, the AS5270A/B position sensors enable automotive OEMs to comply with the highest safety standards
German versionPremstaetten, Austria (5 July, 2017) -- ams (SIX: AMS), a leading worldwide supplier of high performance sensor solutions, announces a new series of magnetic position sensors with increased safety and diagnostic capabilities to help automotive OEMs achieve the highest in ISO26262 ASIL system safety-level compliance.
The AS5270A/B devices are ideal for many automotive applications including brake and gas pedals, throttle valve and tumble flaps, steering wheel position, chassis ride-height, Exhaust Gas Recirculation (EGR) valves, fuel-level measurement systems, and 2/4 wheel drive switching.
The new AS5270A and AS5270B system-on-chip (SOC) devices are 0 to 360o rotary magnetic position sensors, that provide contactless high resolution, absolute angle measurements. The AS5270A/B were developed as SEooC (Safety Element out of Context) devices, as defined per the ISO26262 functional safety standard specification.
The AS5270A/B magnetic position sensors provide on-chip full datapath diagnostics, that test the entire device, from the Hall sensor front end, through the DSP engine that converts raw measurements of magnetic field strength into sine and cosine vectors, to the back-end interfaces and pins.
The AS5270A/B are stacked and aligned dual-die devices, AEC-Q100 Grade 0 qualified and come in MLF-16 surface mount packages for high-reliability and redundant operations. Separate package pins are provided for each die in order to avoid electrical fault in the device from affecting both dies.
With an internal 14-bit (0.022o) resolution front-end core Hall sensor array, the AS5270A/B devices provide true 12-bit output resolution. The high sensitivity Hall sensor front-ends also enable the devices to work with small, lower cost target magnets and support a wide magnetic field strength input range of 10-90mT.
The AS5270A provides an analog output, and the AS5270B provides either a digital SENT (Single Edge Nibble Transmission) or PWM (Pulse Width Modulation) output that is customer programmable. Both devices also support customer programmable angular range limit clamps, digital filtering, and output linearization features. In addition, with the AS5270B there are customer programmable settings for various SENT and PWM interface protocol features. For both devices, one wire programming is accomplished via the output pin, and due to onboard charge-pumps no high voltage programming levels are required. Once the one-time-programmable (OTP) fuses are blown, there is no possibility of the devices becoming inadvertently or maliciously reprogrammed, thus further reducing automotive safety risks.
The AS5270A/B position sensors operate off of a 5V supply voltage, and the supply and output pins are protected against overvoltage up to +20V. In addition, the supply pins are protected against reverse polarity up to –20V.
The AS5270A/B devices are immune to magnetic stray fields, thus ensuring highly accurate and repeatable measurements even in the nosiest of magnetic environments. This results in very reliable performance and reduced system cost, since there is no need for sophisticated shielding that is typically required by competitive magnetic position sensor ICs.
“The release of our AS5270A/B devices represents ams’ continued commitment to supporting the evolving functional safety requirements of our automotive customers”, said Marcel Urban, Head of Marketing and Product Management for position sensors at ams. “ams’ new magnetic position sensors offer integrated safety support features, providing automotive OEMs with a more robust set of diagnostic and self-test features in a magnetic position sensor than ever before, and as a result, enabling them to achieve the highest in ISO26262 safety standards compliance.”
The AS5270A/B magnetic position sensors are available immediately in production volumes. Unit pricing is US$ 3.98 for AS5270A/B in order quantities of 1.000.
Evaluation boards for the AS5270A/B are available from the ams ICdirect online store.
For sample requests and for more technical information, please go to AS5270.
Premstätten, Österreich (5. Juli 2017) -- ams (SIX: AMS), ein weltweit führender Anbieter von Hochleistungs-Sensoren, kündigt eine neue Serie von magnetischen Winkelsensoren mit verbesserten Sicherheits- und Diagnosefähigkeiten an. Automobilhersteller und –zulieferer können damit höchste Sicherheitseinstufungen nach ISO26262 (automotiver Standard für Funktionale Sicherheit) erfüllen.
Die neuen AS5270A und AS5270B Bausteine sind magnetische Winkelsensoren für die kontaktlose, hochauflösende und absolute Winkelmessung von 0° bis 360o. Zielapplikationen für AS5270A/B Chips sind unter anderem Brems- und Gaspedale, Abgasrückführventile und Tumbleklappen, Lenkradstellung, Karosserie-Höhenstand und Füllstandsmessung.
Die AS5270A/B Bausteine wurden gemäß ISO26262 als SEooC (Safety Element out of Context) Bausteine spezifiziert und entwickelt. Dadurch entfällt die bisher notwendige aufwendige individuelle Abstimmung zwischen IC-Hersteller und Anwender, um Sicherheitseinstufungen nach ASIL zu erreichen. Das ermöglicht Kosteneinsparungen bei der Entwicklung und eine deutliche Verkürzung der Entwicklungszyklen.
Die AS5270A/B Sensoren bieten eine vollständige On-Chip-Datenpfad-Diagnostik, die den gesamten Baustein testet, vom Hall-Sensor front-end über den Digitalteil bis zum Interface.
Die AS5270A/B Bausteine werden im stack-die MLF (QFN) 16pin Gehäuse geliefert und sind qualifiziert gemäß AEC-Q100 grade 0 für 150°C Umgebungstemperatur. Die Chip-auf-Chip Stapeltechnologie ermöglicht volle Redundanz und exakten Messwertgleichlauf in einem einzigen Gehäuse. Das ist entscheidend für viele sicherheitskritische Anwendungen wie Lenkwinkel oder Pedalstellung.
Die interne Signalverarbeitung im Baustein erfolgt mit einer 14-bit (0.022°) Auflösung, so dass der AS5270A/B Baustein eine echte 12-bit-Auflösung am Ausgang bereitstellt.
Die AS5270A/B Bausteine können in einem breiten Eingangsbereich von magnetischen Feldstärken von 90mT bis zu minimal 10mT messen und ermöglichen so, mit sehr kleinen und kostengün-stigeren Magneten zu arbeiten.
Der AS5270A/B Familie bietet analoge und digitale Ausgangsformate. Der AS5270B verfügt über einen digitalen SENT- (Single Edge Nibble Transmission) oder PWM- (Pulsbreitenmodulation) Ausgang, der vom Nutzer programmierbar ist. Der AS5270A bietet einen ratiometrischen 5V Analog-Ausgang.
Zusätzlich gibt es beim AS5270B nutzerprogrammierbare Einstellungen für viele SENT- und PWM-Interface-Features. Beide Bausteine verfügen ebenfalls über vom Nutzer programmierbare Winkelbereiche und Bereichsgrenzen, digitale Filter und Linearisierungsmöglichkeiten.
Bei beiden Bausteinen erfolgt die Programmierung mit Hilfe eines hochzuverlässigen OTP (One-Time Programming) Speichers über den Ausgangspin. OTP Speicher sind besonders sicher gegen ungewollte Umprogrammierung in der Anwendung.
Die AS5270A/B Sensoren arbeiten mit 5V Betriebsspannung. Die Stromversorgungs-Pins und der Output-Pin sind gegen eine Überspannung von bis zu +20V (Batterieschluss) geschützt. Zusätzlicher Schutz besteht an den Stromversorgungs-Pins gegen eine umgekehrte Polarität von bis zu -20V.
Durch die patentierte differentielle Architektur sind die AS5270A/B-Chips unempfindlich gegenüber magnetischen Streufeldern. Zuverlässige und genaue Messungen in Gegenwart starker Magnetfelder wie sie in Fahrzeugen mit elektrischem Antrieb (EV, HEV) bzw. bei elektrischen Motoren für Lenkungsunterstützung auftreten sind damit gewährleistet. Eine kostentreibende Abschirmung der AS5270A/B Sensoren gegen diese Felder ist nicht notwendig.
“Die Markteinführung unserer AS5270A/B-Bausteine zeigt das klare Bekenntnis von ams, unsere Kunden in der Automobilbranche bei den steigenden Sicherheitsanforderungen zu unterstützen”, so Marcel Urban, Leiter der Abteilung Marketing und Product Management für Positionssensoren bei ams.
“ams neue magnetische Winkelsensoren bieten integrierte Sicherheitsfeatures, die Automobilherstellern und -zulieferern die Möglichkeit geben, die höchsten Sicherheitsstandards nach ISO26262 zu erfüllen. Im Gegensatz zu unseren Mitbewerbern sind alle ams Winkelsensoren darüber hinaus robust gegen den Einfluss magnetischer Fremdfelder und sind damit besonders für den Einsatz in elektrifizierten Fahrzeugen (HEV, EV) geeignet"
Die AS5270A/B magnetischen Positionssensoren sind ab sofort in Produktionsmengen verfügbar. Der Stückpreis ist US$ 3.98 für AS5270A/B bei Bestellung von 1.000 Stück.
Evaluation-Boards für die AS5270A/B sind im ams ICdirect Online Store verfügbar.
Bei Anfragen für Muster und für weitere technische Informationen besuchen Sie bitte unsere Web-site unter AS5270.